EOC100-P30-K PoE over Coaxial/UTP Converter, 500m, 100Mbps, Up to 30W
- Ethernet and PoE extension over coaxial cable or twisted pair
- Up to 500m rated transmission distance
- 100Mbps physical link, up to 94Mbps TCP throughput
- IEEE 802.3af/at-compatible PoE output, up to 30W
- TX/RX converter configuration with BNC or Phoenix terminal connections
- IGMP multicast support, plug-and-play operation
$89.99
200 in stock
200 in stock
Description
Product Overview
The Sailtel EOC100-P30-K PoE over Coaxial/UTP Converter is a network transmission solution designed to carry 10/100Mbps Ethernet data over existing coaxial cable or twisted-pair wiring. It uses complementary TX (transmitter) and RX (receiver) endpoints for extended network links of up to 500 meters under suitable installation conditions.
Designed for applications such as security monitoring, IP surveillance and industrial connectivity, the solution supports IEEE 802.3af/at-compatible PoE output with a maximum rated 30W power level. The technical specification lists a 100Mbps physical-layer transmission rate and a maximum TCP throughput of approximately 94Mbps. Actual performance depends on the cable and installation.
Key Features
- Long-distance link: rated communication distance up to 500m over compatible coaxial or twisted-pair cabling
- Ethernet: 100Mbps physical-layer speed; 10Mbps-compatible, up to 94Mbps specified TCP throughput
- PoE output: IEEE 802.3af/at-compatible PSE functionality; maximum 30W specified in the product overview
- IGMP: bidirectional propagation / multicast support
- Plug and play: self-organizing connection between converter endpoints
- Designed for continuous operation: 7 × 24-hour use; metallic shielding enclosure
- Cable connectors: BNC coaxial interface or 2 × 3.81mm Phoenix terminal for transmission
Applications
Designed for extending Ethernet data and compatible PoE connections across existing coaxial or twisted-pair cable runs, especially in IP camera networks, facility security, campus monitoring and industrial sites where installing new Ethernet cable is difficult.
Connection & Selection Guide
TX and RX: The product imagery shows separate blue-labeled TX and orange-labeled RX devices. Verify the required ends, topology and whether your purchase includes both converters before placing an order; the technical specification does not explicitly define standard package quantities.
Existing cabling: Confirm cable condition, connector type (BNC or Phoenix terminal), signal attenuation and the length of the run. The 500m figure is an upper rated communication distance, not a guaranteed result for every installation.
PoE compatibility: Check the remote powered device’s actual 802.3af/at requirements and total power load. For 30W-class operation, ensure adequate DC input and that the complete transmitter/receiver configuration supports the planned wiring.
Specification note: Datasheet V1.0 lists operating temperature -10°C to +70°C in the specifications table; an earlier overview paragraph states up to +75°C. The table value is used on this draft page pending confirmation. The dimensions table specifies 96 × 53 × 22mm excluding connectors, while a supplied illustration labels the length 106mm; confirm the mechanical drawing before installation.
Technical Support & After-Sales
Send your cable type, link distance, camera or powered-device model, and intended installation layout to support@sailtel.com for assistance. See Shipping, Returns & Refunds for the store’s current service policy.
Technical Specifications
Overview
| Model | EOC100-P30-K |
|---|---|
| Product Type | PoE over Coaxial/UTP Ethernet Converter |
| Transmission Arrangement | Complementary TX / RX endpoints |
| Transmission Medium | Coaxial cable / twisted pair / suitable network cable |
| Maximum Rated Transmission Distance | 500m |
| Physical-Layer Data Rate | 100Mbps |
| Ethernet Compatibility | 100Mbps standard, 10Mbps compatible |
| Maximum Specified TCP Throughput | 94Mbps |
| Multicast | IGMP multicast; bidirectional propagation |
| PoE Power Source Type | PSE, IEEE 802.3af/at-compatible |
| Maximum Rated PoE Output | 30W (overview statement; verify device configuration) |
| DC Input | 44–56V DC ±10%; at least 1A per datasheet |
| Self Power Consumption | ≤ 2W |
| Ethernet Connector | RJ45, pairs 1/2 and 3/6 specified |
| Long-Distance Interface | BNC coaxial socket or 2 × 3.81mm Phoenix terminal |
| DC Power Connector | Round DC socket, listed as 2.1–5.5mm |
| Indicators | Power, Link, RJ45 yellow PoE, RJ45 green E-Link |
| Operating Temperature | -10°C to +70°C (Specifications table, V1.0) |
| Storage Temperature | -40°C to +85°C |
| Humidity | 0–95% (datasheet) |
| Enclosure Color | Black |
| Material / Shielding | Metal shielding enclosure (overview) |
| Dimensions | 96 × 53 × 22mm excluding connectors (V1.0 table) |
| Net Weight | Approx. 88.5g (per datasheet; pack quantity unconfirmed) |
| Operation | 7 × 24h, plug-and-play |
Datasheet & Downloads
Frequently Asked Questions
What is the maximum supported distance?
Up to 10km on suitable single-mode fiber, subject to the link budget and connector loss.
Which optical wavelength and connector does it use?
A nominal 1310nm optical wavelength and duplex LC interface.
Is the module compatible with multimode fiber?
This model is specified for single-mode fiber. Select an appropriate multimode transceiver if your installation uses MMF.
What speed does it support?
It is designed for 10GBASE-LR applications at a 10.3125Gbps line rate, not for 1G SFP operation.
Does it support DDM / DOM?
Yes. Digital diagnostic monitoring is supported when the host equipment exposes these readings.
Can I insert it while equipment is powered on?
Yes, in a compatible hot-pluggable SFP+ host. Follow your device manufacturer's procedures.
Will it work with any brand of switch?
Not automatically. Check the host brand, model, firmware and vendor coding requirements before ordering.
Reviews
Clear filtersThere are no reviews yet.